Dołączył: 29 Lip 2020
|Wysłany: Czw Gru 31, 2020 03:37 Temat postu: Presently, the industry is produced.
|Presently, the industry is produced. No matter what type of machine equipment, fitness equipment, furniture, etc.,There are almost structural steel plumbing and oil pipes pertaining to oil, gas, fluid infusion, and they occupy necessary position in fitness products. The large number with various tube types and their complex forms have got brought many difficulties towards the processing of catheters.
- Safety precautions for tv bender operation
- Iron bending machine operating methods
- Regularization of tube bender
Safety precautions to get tube bender operation
ONE. When the machine program is started, be careful to not enter the swept range belonging to the rotating arm.
2. When the machine tool is doing work, all personnel are prohibited from entering space swept by the boom in addition to pipe bender fittings!
THREE. The hydraulic system on the roller bending machine device adopts YA-N32 ordinary hydraulic oil (formerly No. 20), which ought to be replaced once a year under normal circumstances, and the oil separate out must be cleaned at the same time.
4. When adjusting the device tool (mold), the adjuster have to press the button to adjust. Never make adjustments by one person around the machine and the other around the control cabinet.
5. The core rod needs to be removed when adjusting the equipment tool or driving a empty car.
6. The pressure with the hydraulic system should not be a lot more than 14 Mpa.
7. When manually adjusting the pace of the side thrust cylinder, the rotating arm should be adjusted when it is rotated to â‰¥900. The adjustment speed is synchronized while using linear speed of exploding of the rotating elbow mold. It is forbidden to push the side pushing faster than the line of the edge of the rotating mold in the manual state. speed.
8-10. After using the general machine for time, check the tightness belonging to the chain to keep top of the and lower chains tiny.
9. During automatic operation within the core bending mode, ahead of the pipe bending arm dividends, the operator must make sure the core head is at the tube, or ensure that the core shaft just isn't blocked when the bending arm returns, otherwise, the core head or core rod may be Bend or break.
TEN. After the work is over, cut off the power supply and do a great job of cleaning as well as lubricating.
Steel bending unit operating procedures
1. The slicer tool must be well grounded, and the wire shall not be a lot less than 4mm2 copper soft insert. It is not allowed for connecting to a power supply voltage exceeding the desired range, plug-ins can not always be plugged in and out of the plug when power is actually on, and the control circuit can't be tested with a megohm meter, otherwise the 780 may be damaged.
TWO. When plugging and unplugging the connector, do not pull the wire or cable to counteract the welding from pushing off.
3. Proximity knobs, encoders, etc. cannot always be hit by hard stuff.
4. Do not struck the display unit having sharp objects..
5. The electrical box has to be placed in a ventilated position, and it is forbidden to work in dust and corrosive un wanted gas.
6. It is banned to install or change the PC input plus output terminals without authorization.
7. When changing the power supply of the unit tool, the motor rotation direction should be reconfirmed.
8. The roller bending machine tool need to be kept clean, and special attention need to be paid to that there ought to be no foreign matter while in the sliding grooves such seeing that clamping blocks and sliding off the road blocks.
9. Lubricate the chain along with sliding parts regularly.
TWELVE. The power must possibly be disconnected during cleaning along with maintenance.
11. Preparation just before driving: Check whether the oil level of the fuel tank grows to the oil level tier, add oil to every single lubrication point, turn on the machine to confirm the rotation in the motor, check the gas pump for abnormal noise, and check whether the hydraulic system is leaking after turning around the machine (the angle encoder is not really allowed Come on);
10. Pressure adjustment: use electromagnetic overflow control device to adjust the pressure so the system pressure reaches the required working pressure, generally not more than 12. 5 Mpa.
TOUGH LUCK. Mold adjustment: mold installation requires mold and clamping block being centered, clamping block is usually adjusted with bolts; the booster block is centered together with mold, booster block is definitely adjustable; core head is centered with mold, loosen core head frame Bolt, fasten the bolt after altering the center.
Regularization associated with pipe bender
When developing and arranging pipe benders, stay clear of excessively large arcs, human judgements curves, compound bends and greater than 180. The arc. The excessively large arc not only makes the tooling cumbersome, but also is limited from the size of the pipe bender: the design of arbitrary curves and compound bending is quite unreasonable, which greatly hinders mechanization and automated creation, making it difficult for operators to shed heavy manual labor; More than 180. The arc makes the actual steel bending machine not able to unload the mold.